• Suitable for use as an admixture to reduce drying time in cementitious levelling screeds and fine concretes for bonded, unbonded and floating screeds. 
• Suitable for moisture sensitive floor coverings.

• Suitable for use as an admixture to reduce drying time in cementitious levelling screeds and fine concretes for bonded, unbonded and floating screeds. 
• Suitable for moisture sensitive floor coverings.

• Suitable for use as an admixture to reduce drying time in cementitious levelling screeds and fine concretes for bonded, unbonded and floating screeds. 
• Suitable for moisture sensitive floor coverings.

RonaScreed FastDry Prompt is a fast-drying additive for site batched screeds used to quickly reduce the level of retained moisture within the screed. This allows floor coverings to be laid over the screed much sooner than with conventional screeds.

RonaScreed FastDry Prompt gains strength quickly, permitting early access by following trades. Drying of screeds incorporating RonaScreed FastDry Prompt is influenced by heat generated during curing, meaning drying of thicker screeds is faster per mm.

Features and benefits:

• Concrete colour with variable texture according to finish applied.
• Enhances early strength gain, enabling earlier trafficking.
• Ready to overlay with floor finishes after eight days at 50 mm thick in good drying conditions; rate of drying extends for screeds thicker than 50 mm.
• Minimum application thickness: 35 mm bonded, 50 mm unbonded and 65 mm floating.

Application (bonded screed):

• Prepare substrate in accordance with instructions.
• Prime substrate with Ronafix or cement slurry.
• Apply screed with maximum layer thickness 50 mm.
• Apply multiple layers wet on wet, or prime between layers.
• Polythene cure for 24 hours, then air cure.

RonaScreed FastDry Prompt is a fast-drying additive for site batched screeds used to quickly reduce the level of retained moisture within the screed. This allows floor coverings to be laid over the screed much sooner than with conventional screeds.

RonaScreed FastDry Prompt gains strength quickly, permitting early access by following trades. Drying of screeds incorporating RonaScreed FastDry Prompt is influenced by heat generated during curing, meaning drying of thicker screeds is faster per mm.

Features and benefits:

• Concrete colour with variable texture according to finish applied.
• Enhances early strength gain, enabling earlier trafficking.
• Ready to overlay with floor finishes after eight days at 50 mm thick in good drying conditions; rate of drying extends for screeds thicker than 50 mm.
• Minimum application thickness: 35 mm bonded, 50 mm unbonded and 65 mm floating.

Application (bonded screed):

• Prepare substrate in accordance with instructions.
• Prime substrate with Ronafix or cement slurry.
• Apply screed with maximum layer thickness 50 mm.
• Apply multiple layers wet on wet, or prime between layers.
• Polythene cure for 24 hours, then air cure.

RonaScreed FastDry Prompt is a fast-drying additive for site batched screeds used to quickly reduce the level of retained moisture within the screed. This allows floor coverings to be laid over the screed much sooner than with conventional screeds.

RonaScreed FastDry Prompt gains strength quickly, permitting early access by following trades. Drying of screeds incorporating RonaScreed FastDry Prompt is influenced by heat generated during curing, meaning drying of thicker screeds is faster per mm.

Features and benefits:

• Concrete colour with variable texture according to finish applied.
• Enhances early strength gain, enabling earlier trafficking.
• Ready to overlay with floor finishes after eight days at 50 mm thick in good drying conditions; rate of drying extends for screeds thicker than 50 mm.
• Minimum application thickness: 35 mm bonded, 50 mm unbonded and 65 mm floating.

Application (bonded screed):

• Prepare substrate in accordance with instructions.
• Prime substrate with Ronafix or cement slurry.
• Apply screed with maximum layer thickness 50 mm.
• Apply multiple layers wet on wet, or prime between layers.
• Polythene cure for 24 hours, then air cure.