Verified by manufacturer 7 months ago
BBA Agrément Certificate
Certificate type
CCPI System
Certificate type
EPD
Certificate type
Two-layer, torch-applied, warm roof bitumen membrane waterproofing system suitable for new build and refurbishment applications, incorporating torch-on bitumen root resistant capping sheet.
Suitable for a variety of applications on both new build and refurbishment projects and can be used in warm, cold and inverted roof scenarios.
Two-layer, torch-applied, warm roof bitumen membrane waterproofing system, suitable for both new build and refurbishment applications on non-combustible substrates (i.e. concrete).
Total green warm roof system, two-layer, torch-applied, warm roof, bitumen membrane waterproofing system, insulation and torch-applied bitumen air and vapour control layer (AVCL).
Total Green Roof System is suitable for a variety of applications on both new build and refurbishment projects and can be used in warm, cold and inverted roof scenarios.
Plus points:
Verified properties:
Color | Green Guidance for specification option: Mineral finish is green. |
Finish | Mineral |
Material | Bitumen Guidance for specification option: Elastomer modified bitumen membrane. |
Shape | Square Rectangle |
Warranty description | Manufacturer guidanceGuarantee options could include ‘Product’, ‘Product and Workmanship’ and ‘Product, Workmanship and Design’ Guarantees. All guarantees available for this system are subject to the works being carried out in accordance with the Bauder specification and being installed by a Bauder Approved installer. For full details and further information regarding guarantees and alternative systems please contact the local Bauder Representative or technical@bauder.co.uk. |
Uniclass | |
CAWS | J41/110 Built-up reinforced bitumen membrane warm deck roof covering J41/10 Reinforced bitumen membrane warm deck roof covering |
Preparation | |
Horizontal work | Bauder Quick Dry Bitumen Primer.Guidance for specification option: A bitumen-based primer applied by a roller or brush. ‘Quick Dry’ is in comparison to standard bitumen primers. Specially formulated to increase the bond strength of Bauder torch-on bitumen membranes and Bauder Hot Melt waterproofing.
Manufacturer guidanceContact manufacturer to confirm substrate suitability if required. |
Skirtings and vertical work | As 'Horizontal work'. |
Air and vapour control layer | |
Type | Bauder Super AL-E.Guidance for specification option: A robust, torch-applied, styrene-butadiene-styrene (SBS) elastomeric bitumen air and vapour control layer, featuring a tear-resistant aluminium foil lining for vapour impermeability. Once installed, the product provides a temporary waterproofing layer, allowing internal works to be carried out immediately.
|
Attachment | Torch applied. |
Insulation | |
Type | BauderGLAS Flatboard.Guidance for specification option: Insert required thickness.
Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge. Suitable for projects that require a high level of compressive strength and/ or to be non-combustible.
BauderGLAS Tapered.Guidance for specification option: Insert required thickness.
Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge. Suitable for projects that require a high level of compressive strength and/ or to be non-combustible.
BauderROCK Flatboard.Guidance for specification option: Insert required thickness.
Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge or mechanically fixed. Mineral fibre insulation, suitable for projects that require a high level of sound reduction and/ or to be non-combustible; it has a zero GWP and ODP rating.
BauderROCK Tapered.Guidance for specification option: Insert required thickness.
Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge or mechanically fixed. Mineral fibre insulation, suitable for projects that require a high level of sound reduction and/ or to be non-combustible; it has a zero GWP and ODP rating.
|
Fixing | PU Insulation Adhesive – Tin.Guidance for specification option: Not for foil to foil applications (e.g. FA-TE to FA-TE). PU Insulation Adhesive – Twin cartridge. |
Waterproof covering | |
First layer | |
Type | BauderFLEX G4E.Guidance for specification option: A 4 mm, heavy-duty, torch-applied elastomeric bitumen underlayer with a strong woven glass reinforcement to provide an extremely high tensile strength.
|
Attachment | Torch applied. |
Top layer | |
Type | PLANT E.Guidance for specification option: A high quality, heavy duty, torch-applied, elastomeric bitumen capping sheet. The product features chemically treated bitumen to deliver superior root resistance which has been tested and approved by the FLL. The membrane is reinforced with 250 g/m² spunbond polyester fleece to allow the finished product to cope with structural movement without fracture. Expandable graphite fire retardant is also incorporated to reduce spread of flame.
|
Attachment | Torch applied. |
Detail work | |
Flashings | Not required.Bauder GRP Trim.Guidance for specification option: GRP roof edge trim for use with Bauder bituminous roof systems. Available in colours of either grey or black, and a choice of profiles to suit the requirements of most projects. Consult manufacturer literature and insert requirements. Bauder GRP Water Check Trim.Guidance for specification option: GRP water check trim to be used on parapets and perimeter kerbs wider than 200 mm – must not be used on its own as a check kerb. Available in black only. Bauder Aluminium Termination Bar.Guidance for specification option: Natural finish aluminium alternative to a lead counterflashing for use at upstand details to give protection to the top edge of the waterproofing. It should be restricted to use on upstands where a chase cannot be cut into the wall. Bauder GRP Termination Bar.Guidance for specification option: Black glass reinforced plastic (GRP) alternative to a lead counterflashing for use at upstand details to give protection to the top edge of the waterproofing. It should be restricted to use on upstands where a chase cannot be cut into the wall. |
Skirtings and upstands | Not required.Bauder LiquiFIBRE Detailing Kit.Guidance for specification option: Fast-curing waterproofing resin, containing fibre reinforcement that can be used for detailing awkward shapes or inaccessible areas where using LiquiDETAIL is impractical. PMMA-based resin that requires a catalyst and is solvent, isocyanate and halogen-free. Bauder LiquiDETAIL.Guidance for specification option: Cold liquid applied fast curing waterproofing resin that can be used on upstands and details. PMMA-based resin that requires the addition of catalyst to trigger curing and is solvent, isocyanate and halogen free. |
Welted drips | Required.Guidance for specification option: Insert requirements. Not required. |
Cover strips | Required.Guidance for specification option: Insert requirements. Not required. |
Ancillary items | Required.Guidance for specification option: Insert requirements. Not required. |
Surface protection | Not required.Landscaping options.Guidance for specification option: Please refer to Bauder Extensive / Biodiverse / Intensive Landscaping systems. |
System accessories | Not required.Bauder lightning conductors.Guidance for specification option: Lightning conductor clips are a specially designed secure clip that allows for movement.
Bauder rainwater outlets.Guidance for specification option: Bauder has a range of insulated or stainless-steel rainwater outlets. The insulated outlets can be used for maintaining thermal continuity at drainage points. Suitable for warm, cold and inverted roof construction, the high thermal value of the rigid foam body prevents condensation from forming on the underside of the outlet. Designed for use when connecting to conventional drainage systems, with excellent flow rate performance and is suitable for both new build and refurbishment projects. Outlets are included in the Bauder waterproofing system guarantee as they are integrated components. Flow rate figures (where applicable) are based on BS EN 12056:3:2000, typically taken using a 35 mm header of water including leaf grille:
Bauder rooflights/ glazing/ ventilation.Guidance for specification option: All these glazing products are fully compatible with the roof waterproofing systems. Consult manufacturer for details and insert requirements.
|
NBS BIM Object Standard
This BIM object has been authored to meet the requirements of the NBS BIM Object Standard.
Find out more about the NBS BIM Object Standard.
Platform | Compatible | Version |
---|---|---|
- | 1 | |
- | 1 |
Bauder System Airtech Warm Roof System - Self Adhered
Bauder Total Green Roof System PLUS Reinforced Bitumen Membrane Warm Roof Covering System Self-Adhered (with Torch-On Capping Sheet)
Bauder Total Green Roof System Reinforced Bitumen Membrane Warm Roof Covering System Self-Adhered (with Torch-On Capping Sheet)
Bauder Total Warm Roof System - Self Adhered
Bauder Total Warm Roof System - Torch Applied
Bauder Total Warm Roof System PLUS - Self Adhered
Bauderflex Green Warm Roof System - Self Adhered (with Torch-On Capping Sheet)
Bauderflex Warm Roof System - Self Adhered
Bauderflex Warm Roof System - Torch Applied