Bauder Total Green Roof System Reinforced Bitumen Membrane Warm Roof Covering System - Torch Applied.

As 'Horizontal work'.

Bauder Super AL-E.

Guidance for specification option:

Torch-applied, styrene-butadiene-styrene (SBS) elastomeric bitumen air and vapour control layer, featuring a tear-resistant aluminium foil lining for vapour impermeability. Once installed, the product provides a temporary waterproofing layer, allowing internal works to be carried out immediately.

• Width: 1 m.
• Length: 7.5 m.
• Thickness: 3.5 mm.
• Surface finish: top: mica; bottom: thermofusible polyethylene.
• Weight: 4.5 kg/m².
• Reinforcement: polyester-coated aluminium foil and 60 g/m² glass fleece.
• Tensile strength: ≥400 N/50mm (length and diagonal).
• Heat stability: +70°C.
• Cold bending test: -20°C.
• Elongation at break: ≥2% (length and diagonal).

Torch applied.

BauderGLAS Flatboard.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge.

Suitable for projects that require a high level of compressive strength and/ or to be non-combustible.

• Type: Cellular glass flatboard insulation board.
• Facing: Glass tissue or none-faced (depending upon system).
• Density: 100 kg/m³.
• Board size: Contact manufacturer for options.
• Thickness (Flatboard): 50 mm, 60 mm, 70 mm, 80 mm, 90 mm, 100 mm, 110 mm, 120 mm, 130 mm, 140 mm, 150 mm, 160 mm, 170 mm, 180 mm, 190 mm, 200 mm (also available in Tapered).
• Thermal conductivity: 0.036 W/m·K (may vary, dependent on thickness specified).
• Compressive strength: 0.5 N/mm².

BauderGLAS Tapered.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge.

Suitable for projects that require a high level of compressive strength and/ or to be non-combustible.

• Type: Cellular glass tapered insulation board.
• Facing: Glass tissue or none-faced (depending upon system).
• Density: 100 kg/m³.
• Board size: Contact manufacturer for options.
• Thickness (maximum): 50 mm, 60 mm, 70 mm, 80 mm, 90 mm, 100 mm, 110 mm, 120 mm, 130 mm, 140 mm, 150 mm, 170 mm, 180 mm. Also available in flat board.
• Thermal conductivity: 0.036 W/m·K (may vary, dependent on thickness specified).
• Compressive strength: 0.5 N/mm².

BauderROCK Flatboard.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge or mechanically fixed.

Mineral fibre insulation, suitable for projects that require a high level of sound reduction and/ or to be non-combustible.

• Type: Dual density mineral wool flatboard.
• Facing: Top: 300 g/m² glass fibre fleece; bottom: unfaced.
• Density: 160 kg/m³.
• Board size: 1200 x 1000 mm.
• Board thickness (Flatboard): 60 mm, 85 mm, 105 mm, 115 mm, 150 mm, 185 mm (also available in tapered).
• Thermal conductivity: 0.039 W/m·K (may vary, dependent on thickness specified).
• Compressive strength: >0.12 N/mm² (minimum 0.08 N/mm²).

BauderROCK Tapered.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge or mechanically fixed.

Mineral fibre insulation, suitable for projects that require a high level of sound reduction and/ or to be non-combustible.

• Type: Tapered insulation board.
• Facing: Top: 300 g/m² glass fibre fleece; bottom: unfaced.
• Density: 160 kg/m³.
• Board size: 1200 x 1000 mm.
• Board thickness (Tapered): 60 mm, 85 mm, 105 mm, 115 mm, 150 mm, 185 mm. Also available in flat board.
• Thermal conductivity: 0.039 W/m·K (may vary, dependent on thickness specified).
• Compressive strength: >0.12 N/mm² (minimum 0.08 N/mm²).

BauderECO FF Flatboard.

Guidance for specification option:

Insert required thickness.

• Type: Rigid closed-cell polyisocyanurate (PIR) roofboard: To BS EN 13165.
• Facing: Crushed shell/glass fleece to both faces.
• Density: >30 kg/m³.
• Standard board size: 1200 x 600 mm.
• Board thickness: 80 mm, 125 mm, 160 mm.
• Thermal conductivity: 0.024 W/m·K (80 mm), 0.023 W/m·K (125 mm and 160 mm).
• Compressive strength: >0.12 N/mm².
• PIR index: >250.

PU Insulation Adhesive – Tin.

Guidance for specification option:

For BauderROCK and BauderGLAS insulation boards, when using Bauder PU Insulation Adhesive - Tin, a ‘water-overmist’ must be applied.

Not for foil-to-foil applications (e.g. FA-TE to FA-TE).

Activator-Primer (Canister) APR01 – Black.

Guidance for specification option:

Not for use with BauderROCK or BauderGLAS insulations.

BauderFLEX G4E.

Guidance for specification option:

A 4 mm-thick, torch-applied elastomeric bitumen underlayer with a woven glass reinforcement to provide tensile strength.

• Width: 1 m.
• Length: 7.5 m.
• Thickness: 4 mm.
• Surface finish: Top: mica; bottom: thermofusible polyethylene.
• Weight: 4.8 kg/m².
• Tensile strength: ≥1200 N/50mm (length and diagonal).
• Heat stability: +110°C.
• Cold bending test: -30°C.
• Elongation at break: ≥2% (length and diagonal).

Torch applied.

BauderPLANT E.

Guidance for specification option:

Elastomer-bitumen capping sheet with root-resistance according to the FLL. The membrane is reinforced with 250 g/m² spunbond polyester fleece to allow the finished product to cope with structural movement without fracture. Expandable graphite fire retardant is also incorporated to reduce spread of flame.

• Width: 1 m.
• Length: 5 m.
• Thickness: 5.2 mm.
• Weight: 6 kg/m².
• Surface, top: green slate mineral chippings; bottom: thermofusible polyethylene.
• Reinforcement: 250 g/m² recycled spunbond polyester.
• Cold bending test: -36°C.
• Softening point: >120°C.
• Tensile strength: length >1000 N/50 mm; transverse >1000 N/50mm.
• Elongation at break: length >45%; transverse >45%.

Torch applied.

Bauder GRP Trim.

Guidance for specification option:

GRP roof edge trim for use with Bauder bituminous roof systems. Available colours of either grey or black and a choice of profiles to suit the requirements of most projects.

Bauder GRP Water Check Trim.

Guidance for specification option:

GRP water check trim to be used on parapets and perimeter kerbs wider than 200 mm – must not be used on its own as a check kerb. Available in black only.

Bauder Aluminium Termination Bar.

Guidance for specification option:

Natural finish aluminium alternative to a lead counterflashing for use at upstand details to give protection to the top edge of the waterproofing. It should be restricted to use on upstands where a chase cannot be cut into the wall.

Bauder GRP Termination Bar.

Guidance for specification option:

Black glass reinforced plastic (GRP) alternative to a lead counterflashing for use at upstand details to give protection to the top edge of the waterproofing. It should be restricted to use on upstands where a chase cannot be cut into the wall.

Not required.

Bauder LiquiFIBRE Detailing Kit.

Guidance for specification option:

Fast-curing waterproofing resin, containing fibre reinforcement that can be used for detailing awkward shapes or inaccessible areas where using LiquiDETAIL is impractical. PMMA-based resin that requires a catalyst and is solvent-free, isocyanate-free and halogen-free.

Bauder LiquiDETAIL.

Guidance for specification option:

Cold liquid-applied fast-curing waterproofing resin that can be used on upstands and details. PMMA-based resin that requires the addition of catalyst to trigger curing and is solvent-free, isocyanate-free and halogen-free.

Required.

Guidance for specification option:

Insert requirements.

Not required.

Required.

Guidance for specification option:

Insert requirements.

Not required.

Required.

Guidance for specification option:

Insert requirements.

Not required.

Not required.

Not required.

Bauder lightning conductors.

Guidance for specification option:

Lightning conductor clips are a specially designed secure clip that allows for movement.

• Bauder Lightning conductor clips – Type 4: Polyvinyl chloride (PVC) coated or bare conductor.

Bauder rainwater outlets.

Guidance for specification option:

Bauder has a range of insulated or stainless-steel rainwater outlets.

The insulated outlets can be used for maintaining thermal continuity at drainage points. Suitable for warm, cold and inverted roof construction. The BRE Certified (report no. HPR357-303748) high thermal value of the rigid foam body prevents condensation from forming on the underside of the outlet body.

Designed for use when connecting to conventional drainage systems and is suitable for both new build and refurbishment projects. Outlets are included in the Bauder waterproofing system guarantee as they are integrated components.

Flow rate figures (where applicable) are based on BS EN 12056:3:2000, typically taken using a 35 mm header of water including leaf grille:

• Bauder Bitumen Compact Vertical Outlet DN100: Insulated internal outlet, 6.1 L/s.
• Bauder Bitumen Vertical Outlet DN70: Insulated internal outlet, 7.1 L/s.
• Bauder Bitumen Vertical Outlet DN150: Insulated internal outlet, 7.2 L/s.
• Bauder Bitumen Letterbox Parapet Outlet DN 205 including stainless-steel leaf guard, 2.02 L/s.
• Bauder Bitumen Parapet Outlet DN 100 including stainless-steel leaf guard, 1.06 L/s.
• Bauder Bitumen Vertical Refurb Outlet DN70, designed to ensure the maximum flow rate of the existing downpipe is not exceeded.
• Bauder Bitumen Vertical Refurb Outlet DN95, designed to ensure the maximum flow rate of the existing downpipe is not exceeded.
• Bauder Bitumen Vertical Refurb Outlet DN145, designed to ensure the maximum flow rate of the existing downpipe is not exceeded.
• Bauder Bitumen Parapet ‘Tell-Tale’ Overflow DN50, designed to be used in conjunction with other roof drainage outlets to ensure that there is no water ingress into the build and that the structural load of the roof is not exceeded and provides a visible warning that the roof is holding excessive water.

Bauder rooflights/ glazing/ ventilation.

Guidance for specification option:

All these glazing products are fully compatible with the roof waterproofing systems. Consult manufacturer for details and insert requirements:

• BauderDOME Rooflight.
• Bauder Euroglaze Rooflight.
• BauderFLATGLASS Rooflight.
• Bauder Special Modular Rooflight.
• Bauder Continuous Rooflight.
• Bauder Walk-on Rooflight.
• Bauder Direct Glazing.
• Bauder AOV.
• Bauder Modular Link Glazing.
• Bauder Structural Rooflight.
• Bauder Fire Rated Rooflight.