Name: BOLIDTOP 525 DECO - Resin Flooring System - Flake (Terrazzo style) - Resin flooring system
Brand: Stratum Resin Flooring Limited
SKU: 44NuNYeBAn6QR15X8DQsXR

Color

Manufacturer guidance

39 base colours available from standard range, any colour can be created with a mixing charge applicable. 35 colours of flake available with unlimited combinations.

Material

Polyurethane (PUR)

Shape

Formless

Length

Bespoke

Width

Bespoke

Height

Bespoke

Warranty description

Ten year

Uniclass

Ss_30_42_54_75 Resin flooring systemsPrimary

CAWS

M12/110 Resin flooring

M12/10 Resin flooring

System performance

Manufacturer guidance

Hardwearing yet decorative resin flooring system, installed seamlessly to provide a hygienic and joint-free floor, with the addition of decorative flakes.

Substrate

Testing

Manufacturer guidance

Moisture compression and surface regularity tests to be carried out by Stratum approved installer.

Concrete/screed substrates - Must be installed to SR1 - no more than 3 mm gap anywhere under a 2 m straight edge, anywhere on the floor. - Compressive Strength - must achieve minimum 25+ on Revound Hammer. - Moisture Content - must be less than 2.5% Moisture Content to enable resin to be installed. Test by Calcium Carbide method for accurate reading.

Cement Board substrates - Boards must be fully glued together with manufacturers adhesive along joints. All joints must be Tongue & Grooved - no butted joints are acceptable. - Boards must be kept dry during and after install. - Excess glue to be scraped off following curing.

Raised Access Flooring - access locations must be agreed. Resin flooring can be installed directly over Calcium Sulphate glued panels. Alternatively, 18 mm screed boards can be installed over raised access floor (glued on all joints), and resin applied over.

Preparation

Manufacturer guidance

Surface to be prepared by mechanical grinding, under full extraction to remove surface laitance and contamination. And cracks present within the substrate will need to be repaired prior to continuation with Epoxy products. Surface to be clear of any debris and dust prior to priming by suitable vacuum/extractor.

Levelling screed

Bonded cementitious levelling screed system.

Manufacturer guidance

If a surface regularity of SR1 is not presented, then a levelling screed may be required. Care should be taken to select a product that is compatible with Resin and (if present) Underfloor heating. Important note: crack repairs must still be completed prior to levelling over, as neglecting to would likely lead to reflective cracking.

Primer

Bolidt Universal Primer.

Guidance for specification option:

Bolidtop universal primer consists of two components, based on low-viscous, solvent-free epoxy resins, which have to be mixed into a perfectly homogeneous mass shortly before use.

Manufacturer guidance

Universal Primer to be installed at a minimum consumption rate of 0.2 kg/m². Consumption will vary depending on porosity of substrate.

Resin flooring

Bolidtop 525 + Flakes.

Guidance for specification option:

Bolidtop 525 Compound is a synthetic material, consisting of two components, based on branched polyols and polyisocyanates, which have to be mixed into a perfectly homogeneous mass.

Bolicoat Pn consists of two liquid components and is based on waterborne polyurethane emulsions. If mixed correctly, the two components will form a product with good mechanical and chemical properties.

Bolicoat Pn.

Manufacturer guidance

Bolidtop 525 Compound is installed at a rate of 3 kg/m². Bolicoat Pn is installed at a rate of 0.11 kg/m².

Approximate system thickness is 3 mm.

Surface treatment

Bolidt coating 54720 (textureless anti-slip). Low slip potential (PTV 36+) in accordance with BS 7976-2 in both wet and dry conditions.

Guidance for specification option:

Bolidt coating 54720 consists of two liquid components and is based on a waterborne polyurethane emulsion. When two components are mixed correctly, a product with a hard-elastic character.

Manufacturer guidance

Used instead of Bolicoat Pn.

Movement joints

Type

Duraflex Stainless Steel movement joints.

Manufacturer guidance

Duraflex Stainless Steel movement joints or similar approved.

Resin skirtings and upstands

Skirtings and upstands to match colour of the flooring system.

Manufacturer guidance

Standard skirting detail, formed using pre-fabricated slender skirting profile, overlaid with resin finishing coats to provide a seamless watertight detail. 10 mm radius and up to 150 mm in height.

System accessories

Trims by Dural.

Guidance for specification option:

Trims by Dural or similar approved.

Execution

Manufacturer guidance

Bolidt resin floors must be installed by trained applicators from Stratum Resin Flooring Limited.

System completion

Manufacturer guidance

Once completed, the floor can be protected with breathable + rigid protection after 48 hours. Full chemical cure takes 1 week, although light traffic can resume once protected.

Contains Red List materials

Country of material origin

Europe

Manufacturer guidance

Our materials are sourced from The Netherlands, Germany, Belgium, Finland, Sweden and UK.

Country of product manufacture

Netherlands

Manufacturer guidance

Our polyurethane seamless floors are produced in Hendrik-Ido-Ambacht in Holland, at Bolidt's headquarters.

Recyclability

Manufacturer guidance

The product (Bolidtop 525 Deco) can be taken back at the end of it's life by grinding or peeling. More than 50% of the product can be dismantled and components recycled, and partially renewed for reuse. If the floor requires repair or maintenance, this will be carried out on site. The product has a proven long service life, and will/can remain anchored to the substrate, until the building is demolished, and then recycled.

Color	- Manufacturer guidance 39 base colours available from standard range, any colour can be created with a mixing charge applicable. 35 colours of flake available with unlimited combinations.
Material	Polyurethane (PUR)
Shape	Formless
Length	Bespoke
Width	Bespoke
Height	Bespoke
Warranty description	Ten year

System performance	- Manufacturer guidance Hardwearing yet decorative resin flooring system, installed seamlessly to provide a hygienic and joint-free floor, with the addition of decorative flakes.
Substrate	-
Testing	- Manufacturer guidance Moisture compression and surface regularity tests to be carried out by Stratum approved installer. Concrete/screed substrates - Must be installed to SR1 - no more than 3 mm gap anywhere under a 2 m straight edge, anywhere on the floor. - Compressive Strength - must achieve minimum 25+ on Revound Hammer. - Moisture Content - must be less than 2.5% Moisture Content to enable resin to be installed. Test by Calcium Carbide method for accurate reading. Cement Board substrates - Boards must be fully glued together with manufacturers adhesive along joints. All joints must be Tongue & Grooved - no butted joints are acceptable. - Boards must be kept dry during and after install. - Excess glue to be scraped off following curing. Raised Access Flooring - access locations must be agreed. Resin flooring can be installed directly over Calcium Sulphate glued panels. Alternatively, 18 mm screed boards can be installed over raised access floor (glued on all joints), and resin applied over.
Preparation	- Manufacturer guidance Surface to be prepared by mechanical grinding, under full extraction to remove surface laitance and contamination. And cracks present within the substrate will need to be repaired prior to continuation with Epoxy products. Surface to be clear of any debris and dust prior to priming by suitable vacuum/extractor.
Levelling screed	Bonded cementitious levelling screed system. Manufacturer guidance If a surface regularity of SR1 is not presented, then a levelling screed may be required. Care should be taken to select a product that is compatible with Resin and (if present) Underfloor heating. Important note: crack repairs must still be completed prior to levelling over, as neglecting to would likely lead to reflective cracking.
Primer	Bolidt Universal Primer. Guidance for specification option: Bolidtop universal primer consists of two components, based on low-viscous, solvent-free epoxy resins, which have to be mixed into a perfectly homogeneous mass shortly before use. Manufacturer guidance Universal Primer to be installed at a minimum consumption rate of 0.2 kg/m². Consumption will vary depending on porosity of substrate.
Resin flooring	Bolidtop 525 + Flakes. Guidance for specification option: Bolidtop 525 Compound is a synthetic material, consisting of two components, based on branched polyols and polyisocyanates, which have to be mixed into a perfectly homogeneous mass. Bolicoat Pn consists of two liquid components and is based on waterborne polyurethane emulsions. If mixed correctly, the two components will form a product with good mechanical and chemical properties. Bolicoat Pn. Manufacturer guidance Bolidtop 525 Compound is installed at a rate of 3 kg/m². Bolicoat Pn is installed at a rate of 0.11 kg/m². Approximate system thickness is 3 mm.
Surface treatment	Bolidt coating 54720 (textureless anti-slip). Low slip potential (PTV 36+) in accordance with BS 7976-2 in both wet and dry conditions. Guidance for specification option: Bolidt coating 54720 consists of two liquid components and is based on a waterborne polyurethane emulsion. When two components are mixed correctly, a product with a hard-elastic character. Manufacturer guidance Used instead of Bolicoat Pn.
Movement joints	-
Type	Duraflex Stainless Steel movement joints. Manufacturer guidance Duraflex Stainless Steel movement joints or similar approved.
Resin skirtings and upstands	Skirtings and upstands to match colour of the flooring system. Manufacturer guidance Standard skirting detail, formed using pre-fabricated slender skirting profile, overlaid with resin finishing coats to provide a seamless watertight detail. 10 mm radius and up to 150 mm in height.
System accessories	Trims by Dural. Guidance for specification option: Trims by Dural or similar approved.
Execution	- Manufacturer guidance Bolidt resin floors must be installed by trained applicators from Stratum Resin Flooring Limited.
System completion	- Manufacturer guidance Once completed, the floor can be protected with breathable + rigid protection after 48 hours. Full chemical cure takes 1 week, although light traffic can resume once protected.

Contains Red List materials	No
Country of material origin	Europe Manufacturer guidance Our materials are sourced from The Netherlands, Germany, Belgium, Finland, Sweden and UK.
Country of product manufacture	Netherlands Manufacturer guidance Our polyurethane seamless floors are produced in Hendrik-Ido-Ambacht in Holland, at Bolidt's headquarters.
Recyclability	- Manufacturer guidance The product (Bolidtop 525 Deco) can be taken back at the end of it's life by grinding or peeling. More than 50% of the product can be dismantled and components recycled, and partially renewed for reuse. If the floor requires repair or maintenance, this will be carried out on site. The product has a proven long service life, and will/can remain anchored to the substrate, until the building is demolished, and then recycled.

BOLIDTOP 525 DECO - Resin Flooring System - Flake (Terrazzo style) - Resin flooring system

Application

Description

General information

Color

Manufacturer guidance

Material

Shape

Length

Width

Height

Warranty description

Uniclass

CAWS

Specification data - Resin flooring systems

System performance

Manufacturer guidance

Substrate

Testing

Manufacturer guidance

Preparation

Manufacturer guidance

Levelling screed

Bonded cementitious levelling screed system.

Manufacturer guidance

Primer

Bolidt Universal Primer.

Manufacturer guidance

Resin flooring

Bolidtop 525 + Flakes.

Bolicoat Pn.

Manufacturer guidance

Surface treatment

Bolidt coating 54720 (textureless anti-slip). Low slip potential (PTV 36+) in accordance with BS 7976-2 in both wet and dry conditions.

Manufacturer guidance

Movement joints

Type

Duraflex Stainless Steel movement joints.

Manufacturer guidance

Resin skirtings and upstands

Skirtings and upstands to match colour of the flooring system.

Manufacturer guidance

System accessories

Trims by Dural.

Execution

Manufacturer guidance

System completion

Manufacturer guidance

Colour

Manufacturer guidance

Sustainability data

Contains Red List materials

Country of material origin

Manufacturer guidance

Country of product manufacture

Manufacturer guidance

Recyclability

Manufacturer guidance

Third party certifications

Literature

Case studies