NBS Source
I'm a manufacturer
Compare variants

Stravifloor Deck - Floating Floor System

Verified by manufacturer 2 months ago

Pad – Deck + Channel + 47 x 47 x 30 mm pad

CDM Stravitec Variant:
Third party certifications:
  • ISO 9001 Quality Management

    Certificate type

  • ISO 14001 Environmental Management Systems

    Certificate type

A low-profile floating floor system using a proprietary dovetailed metal deck for thin concrete pours.

Jump to:
BOS
+44 1664 482486 Website

Application

Suitable for projects that require a low-profile or lightweight concrete floating floor. Also suitable for areas with high live loads.

Description

Stravifloor Deck is a low-profile floating floor system using a proprietary dovetailed metal deck for thin concrete pours. The system’s high bending stiffness allows for concrete toppings as thin as 50 mm.


Stravifloor Deck provides a high-performance floating floor system for excellent structure-borne and airborne noise isolation while minimizing any impact on the available floor-ceiling height.


Features and benefits:

  • Stravifloor Deck standard solutions are available with resilient pads in four standard grades: Pad-M (medium stiffness), Pad-H (high stiffness) and Pad-X (extra high stiffness).
  • The system can be changed to meet project specifications in terms of natural frequency and damping requirements, Ln,w or Rw using non-standard bearings.
  • The standard range of resilient pads is available to provide load-bearing capacities from 0.1 to 3 MPa per pad.
  • Uses elastomeric isolators with low stiffness/ high resilience allowing natural frequencies as low as 6 Hz, or springs allowing natural frequencies as low as 2.5 Hz.
  • Steel parts are galvanized.
  • The system allows high bending stiffness specifically for both restricted build-up height and limited extra weight applications (low permanent weight with floor system from only 86 mm total thickness: 36 mm resilient support + 50 mm steel reinforcement sheet with concrete or screed floor).
  • The system is compatible with high permissible loads.
  • High performance floating floor system with large support spans (up to 1200 mm).
  • Quick to install resulting in a cost effective solution.
  • Allows services to be installed within the air void.
  • Easy to incorporate underfloor heating or cooling systems.
  • Isolation pads, used as discrete resilient support of the system, are mold and water resistant.
  • Uses moisture resistant formwork, free of autochthonous parasites or other harmful organisms and is lightweight and easy to handle.

General information

Color

Silver

Finish

Galvanized

Material

Steel

Shape

Other

Length

Bespoke

Width

Bespoke

Height

Bespoke

Manufacturer guidance

Minimum height : 86mm

Warranty description

Ten year

Uniclass

Ss_30_12_85_16 Composite steel and concrete deck systemsPrimary

CAWS

K11/27 Acoustic separating floor system

K11/275 Acoustic separating floor system

K11/295 Floating floor system

Specification data - Composite steel and concrete deck systems

Framing members

Galvanized carbon steel isolated channels.

Manufacturer guidance

Note: the channel spacing - which can be between 400 to 1200 mm - need to be determined by the CDM Stravitec engineering team according the (concrete or screed) floating floor thickness and the load cases in operation phase.

Steel channel standard length: 2 m.

Steel channel standard thickness: 0.75 mm.

Permanent formwork

-

Steel profiled sheet for composite floor slabs and beams

Steel profiled sheet.

Manufacturer guidance

Dovetailed sheeting

Steel thickness: 0.5 mm.

Nominal width: 630 mm.

Effective width: 580 mm.

Standard length: 2200 mm. (Other lengths available upon request.)

Effective length: 2100 mm.

Dimensional tolerances: Length: 1-4 mm; width: 1-3 mm.

Moment of Inertia: Ix = 3.6 cm⁴/m.

Moment of resistance: Wx = 3.0 cm³/m.

Fixings for permanent formwork

-

End support fixings

Up to 20 mm autodrill screws.

Side support fixings

Up to 20 mm autodrill screws.

Ancillary accessories to permanent formwork

Metal L-profile and possible restraint straps as formwork for edges.

In situ concrete topping

C20/25 fine grade aggregate concrete.

CA25F4 free flowing, self levelling, liquid screed.

Manufacturer guidance

Minimum ‘fine grade’ concrete thickness: 16 mm profile height + 34 mm = 50 mm.

Reinforcement

-

Type of reinforcement

Steel mesh.

Manufacturer guidance

The steel mesh necessary to cope with the loads in the finished floor needs to be calculated for the load cases in operation phase (service phase). This needs to be done by a structural engineer (upon request, CDM Stravitec can provide recommendations).

System accessories

Metal L-profile and possible restraint straps for edge formwork, perimeter strips, autodrill screws, etc.

Standards

Rw measured in accordance with ISO 10140-2:2010 (with additional vibration analyses) and single figure ratings determined in accordance with ISO 717-1:2013 by the lab responsible for the measurements. Ln,w and ∆Lw measured in accordance with ISO 10140-3:2010/A1:2015 and single figure ratings determined in accordance with EN ISO 717-2:2013.

Weighted sound reduction index, Rw

79 dB.

Guidance for specification option:

Tested on 140 mm concrete bare slab with 50 mm concrete floating slab.

Manufacturer guidance

Consult manufacturer's literature and/or Stravi-dB (stravi-db.com) for detailed sound reduction index values.

Impact sound reduction

Ln,w: 37 dB; ΔLw: 39 dB.

Guidance for specification option:

Tested on 140 mm concrete bare slab with 50 mm concrete floating slab.

Manufacturer guidance

Consult manufacturer's literature and/or Stravi-dB (stravi-db.com) for detailed sound reduction index values.

Materials

Steel and elastomer.

Designation

S320GD + Z100 N-A-C finishing, according to NEN-EN10147.

Manufacturer guidance

Z275 can be supplied upon request.

System height

86 mm (minimum).

Load capacity

0.1–3 MPa per pad.

Resilient layer

CDM Stravitec resilient pads, Pad-M (medium stiffness).

CDM Stravitec resilient pads, Pad-H (high stiffness).

CDM Stravitec resilient pads, Pad-X (extra high stiffness).

Manufacturer guidance

  • Four standard grades of CDM Stravitec resilient pads are available.
  • The selection of the type of elastomeric pad must be done by the CDM Stravitec engineering team according to the load cases in operation phase as well as the type of application.
  • The channel spacing, as well as the spacing between the pads, needs to be determined by the CDM Stravitec engineering team according to the floating floor thickness and the load cases in the operation phase.

Dimensions

Metal channels 60 x 2000 mm with pads 30 mm thick.

Air gap

36 mm (minimum).

Insulation

Mineral wool.

Guidance for specification option:

Dimensions defined according to project requirements.

Accessories

Perimeter strip, 10 x 50 x 10 000 mm.

Perimeter strip, 10 x 100 x 10 000 mm.

Perimeter strip, 10 x 150 x 10 000 mm.

Perimeter strip, 10 x 200 x 10 000 mm.

Sustainability data

Contains Red List materials

No

Country of material origin

Europe

Country of product manufacture

Europe

Material

Steel

Third party certifications

BIM objects

BOS

NBS BIM Object Standard

This BIM object has been authored to meet the requirements of the NBS BIM Object Standard.

Find out more about the NBS BIM Object Standard.

Platform Compatible Version
Revit
-

4

IFC
-

3

Third party certifications

ISO 9001 Quality Management

ISO 9001 Quality Management

ISO 9001-2015: Quality Management System

ISO 14001 Environmental Management Systems

ISO 14001 Environmental Management Systems

ISO 14001-2015: Environmental Management System

Literature

Datasheet Stravifloor Deck

Datasheet Stravifloor Deck

Installation Manual Stravifloor Deck

Installation Manual Stravifloor Deck

Brochure - Stravifloor

Brochure - Stravifloor

Case studies

Olympia London

Olympia London

Hotel Café Royal

Hotel Café Royal