Bauder Thermofol PVC Warm Roof System - Adhered

TEC KSD Foil.

Guidance for specification option:

Self-adhesive elastomeric bitumen air and vapour control layer (AVCL), with an aluminium foil facing for vapour impermeability. The bottom is a peel off release film, covering self-adhesive bitumen.

• Width: 1 m.
• Length: 15 m.
• Thickness: 1.5 mm.
• Weight: 1.8 kg/m².
• Reinforcement: 60 g/m² glass fleece.
• Tensile strength: Length and Diagonal ≥ 400 N/50mm.
• Cold bending test: -30°C.
• Elongation at break: Length and Diagonal ≥ 2%.

TEC KSD FBS.

Guidance for specification option:

Robust, self-adhesive elastomeric bitumen air and vapour control layer (AVCL), with a mica finished upper surface to allow easy bonding of insulation using appropriate Bauder Insulation Adhesive. One side lap features an 80 mm wide glass fleece along the underside, and a 100 mm strip of aluminium foil above. The other side lap has a thermofusible film on the top surface. This arrangement ensures that laps are heat sealed using hot air or gas torch as appropriate to extrude a bitumen bead, thus ensuring waterproofing integrity.

• Width: 1.08 m.
• Length: 10 m.
• Thickness: 2.5 mm.
• Weight: 2.5 kg/m².
• Reinforcement: Polyester coated aluminium foil and 200 g/m² glass fleece.
• Tensile strength: Length and Diagonal ≥ 1000 N/50mm.
• Cold bending test: -25°C.
• Elongation at break: Length and Diagonal ≥ 2%.

BauderGLAS Flatboard.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge.

Cellular glass insulation suitable for projects that require a high level of compressive strength and/ or to be non-combustible.

• Type: Cellular glass flatboard insulation board.
• Facing: Glass tissue or none faced (depending upon system).
• Density: 100 kg/m³.
• Board size: Contact manufacturer for options.
• Board thickness (Flatboard): 50 mm, 60 mm, 70 mm, 80 mm, 90 mm, 100 mm, 110 mm, 120 mm, 130 mm, 140 mm, 150 mm, 170 mm, 180 mm (also available Tapered).
• Thermal conductivity: 0.036 W/m·K (may vary dependent on thickness specified).
• Compressive strength: 0.5 N/mm².

BauderGLAS Tapered.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – twin cartridge.

Cellular glass insulation suitable for projects that require a high level of compressive strength and/or to be non-combustible.

• Type: Cellular glass tapered insulation board.
• Facing: Glass tissue or none faced (depending upon system).
• Density: 100 kg/m³.
• Board size: Contact manufacturer for options.
• Board thickness (Flatboard): 50 mm, 60 mm, 70 mm, 80 mm, 90 mm, 100 mm, 110 mm, 120 mm, 130 mm, 140 mm, 150 mm, 170 mm, 180 mm (also available Tapered).
• Thermal conductivity: 0.036 W/m·K (may vary dependent on thickness specified).
• Compressive strength: 0.5 N/mm².

BauderROCK Flatboard.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – Twin cartridge or mechanically fixed.

Mineral fibre insulation suitable for projects that require a high level of sound reduction and/ or to be non-combustible and has a zero GWP and ODP rating.

• Type: Dual density mineral wool flatboard insulation board.
• Facing: Top: 300 g/m² glass fibre fleece; Bottom: Unfaced.
• Density: 160 kg/m².
• Board size: 1200 x 1000 mm.
• Board thickness (Flatboard): 60 mm, 85 mm, 105 mm, 115 mm, 150 mm, 170 mm, 185 mm (also available in tapered).
• Thermal conductivity: 0.039 W/m·K (may vary dependent on thickness specified).
• Compressive strength: >0.12 N/mm² (minimum 0.08 N/mm²).

BauderROCK Tapered.

Guidance for specification option:

Insert required thickness.

Can only be used with PU Insulation Adhesive – Tin (with ‘water-overmist’) or PU Insulation Adhesive – Twin cartridge or mechanically fixed.

Mineral fibre insulation suitable for projects that require a high level of sound reduction and/ or to be non-combustible and has a zero GWP and ODP rating.

• Type: Dual density mineral wool flatboard insulation board.
• Facing: Top: 300 g/m² glass fibre fleece; Bottom: Unfaced.
• Density: 160 kg/m².
• Board size: 1200 x 1000 mm.
• Board thickness (Flatboard): 60 mm, 85 mm, 105 mm, 115 mm, 150 mm, 170 mm, 185 mm (also available in tapered).
• Thermal conductivity: 0.039 W/m·K (may vary dependent on thickness specified).
• Compressive strength: >0.12 N/mm² (minimum 0.08 N/mm²).

BauderVIP TE 60 mm Flatboard.

Guidance for specification option:

• Type: Vacuum insulation panel with pyrogenic silica vacuum core, 40 mm.
• Facing: Top: High density PIR, 17 mm; Bottom: Rubber granulate, 3 mm.
• Density: 13 kg/m².
• Standard board sizes: 1000 x 1000 mm and 1000 x 500 mm.
• Standard board thickness: 60 mm.
• Thermal conductivity: 0.009 W/m·K.
• Compressive strength: >0.12 N/mm².

BauderVIP TE 80 mm Flatboard.

Guidance for specification option:

• Type: Vacuum insulation panel with pyrogenic silica vacuum core, 60 mm.
• Facing: Top: High density PIR, 17 mm; Bottom: Rubber granulate, 3 mm.
• Density: 17 kg/m².
• Board sizes: 1000 x 1000 mm, 1000 x 500 mm.
• Board thickness: 80 mm.
• Thermal Conductivity: 0.009 W/m·K.
• Compressive strength: >0.12 N/mm².

PIR FA Flatboard.

Guidance for specification option:

Insert required thickness.

• Type: Rigid closed-cell polyisocyanurate (PIR) roofboard: To BS EN 13165.
• Facing: Black aluminium foil to both faces.
• Density: >30 kg/m³.
• Standard board size: 1200 x 2400 mm.
• Thickness: 60 mm, 80 mm, 100 mm, 120 mm, 140 mm, 160 mm, 180 mm.
• Thermal conductivity: 0.022 W/m·K (may vary dependent on thickness specified).
• Compressive strength: >0.12 N/mm².
• PIR index: >250 (extremely high dimensional stability).

PIR FA G16 foil-faced tapered insulation.

Guidance for specification option:

Insert required thickness.

Only for use with U15 FB Membrane when adhering.

• Type: Rigid closed-cell polyisocyanurate (PIR) roofboard: To BS EN 13165.
• Facing: Black aluminium foil to both faces.
• Density: >30 kg/m³.
• Standard board size: 1200 x 1200 mm.
• Board thickness: Contact manufacturer for options.
• Thermal conductivity: 0.022 W/m·K.
• Compressive strength: >0.12 N/mm².
• PIR index: >250 (extremely high dimensional stability).

PIR FA-TE Flatboard.

Guidance for specification option:

Insert required thickness.

• Type: Rigid closed-cell polyisocyanurate (PIR) roofboard: To BS EN 13165.
• Facing: Aluminium foil to both faces.
• Density: >30 kg/m³.
• Standard board size: 1200 x 600 mm.
• Thickness: 30 mm, 40 mm, 50 mm, 60 mm, 80 mm, 100 mm, 120 mm, 140 mm, 160 mm.
• Thermal conductivity: 0.022 W/m·K (may vary dependent on thickness specified).
• Compressive strength: >0.12 N/mm².
• PIR index: >250 (extremely high dimensional stability).

PU Insulation Adhesive – Tin.

Guidance for specification option:

Not for foil to foil applications (e.g. FA on KSD Foil).

Activator-Primer (Canister) APR01 – Black.

PU Insulation Adhesive – Twin cartridge.

Fleece Backed Membrane Adhesive (Blue) - Drum.

Guidance for specification option:

For adhering U 15 V FR to plywood, concrete, existing bitumen and most other deck/surface types. Suitability to be confirmed with manufacturer.

PU Fleece Backed Membrane Adhesive (Pink) - Canister.

Guidance for specification option:

For adhering U15 V FR to many deck types. Suitability to be confirmed with manufacturer.

Activator Primer (Black) - Canister.

Guidance for specification option:

For adhering U15 V FR to many deck types. (Not suitable for direct application to existing felt). Suitability to confirmed with manufacturer.

Thermofol Contact Adhesive (Red) – Drum.

Guidance for specification option:

For adhering non-fleece backed to most new deck types. Not for adhering to existing bitumen. Suitability to be confirmed with manufacturer.

Not required.

Bauder Thermofol D18 PVC Detailing Membrane.

Guidance for specification option:

• This unreinforced detailing membrane is manufactured from Polyvinyl Chloride membrane (PVC). The product is highly flexible due to the incorporation of internal plasticizers during the manufacturing process. This combination of materials provides high elongation, good thermal stability and flexibility. Complex three-dimensional detailing to curves, pipes or awkward shapes can be formed using Thermofol un-reinforced D18 membrane. Otherwise BauderPVC IE/AE corners must be used at intersections and returns.
• Available in all three membrane colours. Light Grey (RAL 7035), Blue Grey (RAL 7031), Anthracite (RAL 7016).
• Membrane to be either fully bonded using Bauder Thermofol Contact Adhesive – Drum or mechanically fixed according to the construction – refer to the Bauder Single Ply Installation Manual for further guidance.

BauderPVC IE/AE corners.

Guidance for specification option:

Pre-formed PVC internal and external corners for use with Thermofol membrane.

• These products are designed to dress into 90° corners, they can be warmed and manipulated to fit corners over and under 90°. If this is not possible a gusset must be dressed to an internal corner and a piece of D18 unreinforced detailing membrane can be used to an external corner with a ‘thumb print’.
• Internal (90 x 90 mm) and External (150 x 170 mm) pre-formed corners can be reversed to allow them to be used at other junction points to ensure a watertight seal is easy to achieve.
• Pre-formed corners must be fully heat welded from the centre outwards working around each side until the entire patch is welded.
• Available in all three membrane colours: Light Grey (RAL 7035), Blue Grey (RAL 7031), Anthracite (RAL 7016).
• For information contact Bauder Technical Department.

BauderPVC VBL 14 laminated metal sheet.

Guidance for specification option:

• 1.4 mm thick. A 0.6 mm thick, hot dip galvanized steel plate, laminated on one side with 0.8 mm thick layer of Thermofol PVC, for use in creating flashings and detailing.
• Available in all three membrane colours: Light Grey (RAL 7035), Blue Grey (RAL 7031), Anthracite (RAL 7016).
• Bauder Thermofol Coated Metal (1 x 2 m) is supplied in pallet quantities in flat sheet form.
• Full fixing and installation information can be found in the Single Ply Technical installation Guide.

BauderPVC VBL 14 laminated metal.

Guidance for specification option:

• 1.4 mm thick. A 0.6 mm thick, hot dip galvanized steel plate, laminated on one side with 0.8 mm thick layer of Thermofol PVC, for use in creating flashings and detailing.
• Available in all three membrane colours: Light Grey (RAL 7035), Blue Grey (RAL 7031), Anthracite (RAL 7016).
• Each flashing type is supplied in a standard 2 m length.
• Full fixing and installation information can be found in the Single Ply Technical installation Guide.

BauderPVC DP 25, decor profile.

Guidance for specification option:

• Bauder Thermofol PVC decorative Profile to be heat welded to Thermofol PVC membrane, to create a ‘Standing Seam’ effect to roofs.
• Bauder Thermofol Profiles are supplied in 3 m lengths, 35 x 27 mm (W x H).
• Available in all three membrane colours: Light Grey (RAL 7035), Blue Grey (RAL 7031), Anthracite (RAL 7016).

Bauder single ply lightning conductors.

Guidance for specification option:

• A specialist lightning conductor clip riveted to a Bauder membrane base. These clips are available to suit coated 25 x 3 mm conductor tape. The membrane base is Thermofol PVC. The base allows the product to be fully welded to the waterproofing, whilst the clip allows movement of the tape caused by expansion/ contraction.
• Bauder Lightning conductor – Type 4: PVC coated.
• Available in all three membrane colours: Light Grey (RAL 7035), Blue Grey (RAL 7031), Anthracite (RAL 7016).

BauderPVC ABL-R 75 / 110 / 160, vertical outlets.

Guidance for specification option:

• A rigid PVC rainwater outlet enabling Thermofol membrane to be welded to the flange plate. UV stable throughout. The unbacked Thermofol membrane should be heat welded up to the aperture to ensure colour consistency on the roof.
• Rigid PVC base plate in Light Grey: 300 mm (70 DN), 385 mm (100 DN and 150 DN).
• Rigid PVC spigot length: 300 mm.

Bauder outlets are sized to indicate the actual internal diameter of the spigot. For information on non-standard sizes and refurbishment applications, please contact Bauder Technical Department.

• BauderPVC ABL-R 75 vertical outlet for 75mm downpipe: Flow rate 4.6 L/s (including leaf guard).
• BauderPVC ABL-R 110 vertical outlet for 110mm downpipe: Flow rate 5.5 L/s (including leaf guard).
• TBauderPVC ABL-R 160 vertical outlet for 160mm downpipe: Flow rate 6.6 L/s (including leaf guard).

BauderSYN KFK-R UNI universal leaf guard for vertical outlets.

Guidance for specification option:

• A universal leaf guard compatible with Thermofol Rigid PVC rainwater outlets for preventing debris blocking the outlet.
• For outlet spigot dimensions ranging from 60–220 mm. Grip Range Depth: 80–105 mm. This product is UV stable.
• Material: Polyamide.
• Colour: Black.

This Bauder Leaf Guard is designed to fit into Bauder Rigid PVC rainwater outlets. For information on non-standard sizes and refurbishment applications, contact Bauder Technical Department.

Bauder Thermofol Stainless Steel rainwater outlets.

Guidance for specification option:

A high performance stainless steel outlet with factory installed Thermofol membrane flange. Supplied with an O-ring and a wire ball leaf grill.

• Stainless steel base plate: 250 x 250 mm.
• Thermofol membrane flange: 350 x 350 mm (Light Grey/ Blue Grey).
• Stainless steel spigot length: 400 mm.

Bauder outlets are sized to indicate the actual internal diameter of the spigot. For information on non-standard sizes and refurbishment applications, please contact Bauder Technical Department.

• Thermofol Stainless steel Rainwater Outlet DN 70: Flow rate 2.98 L/s (including leaf guard).
• Thermofol Stainless steel Rainwater Outlet DN 100: Flow rate 3.94 L/s (including leaf guard).
• Thermofol Stainless steel Rainwater Outlet DN 150: Flow rate 6.76 L/s (including leaf guard).

BauderPVC DSP-R 110 parapet outlet.

Guidance for specification option:

A rigid PVC parapet rainwater outlet enabling Thermofol membrane to be welded to the flange plate. UV stable throughout. The unbacked Thermofol membrane should be heat welded up to the aperture to ensure colour consistency on the roof.

• Rigid PVC base plate in Light Grey: 280 x 180 x 110 mm (W x H x D).
• Rigid PVC spigot length: 480 mm.
• Thermofol Rigid PVC Rainwater Outlet DN 100: Flow rate 1.0 L/s.

Bauder outlets are sized to indicate the actual internal diameter of the spigot. For information on non-standard sizes and refurbishment applications, contact Bauder Technical Department.

BauderTHERMOFOL PVC Letterbox parapet outlet DN190 including s/s leaf guard.

Guidance for specification option:

A high flow rate PVC parapet outlet for roof drainage systems. Factory bonded membrane flange attached to the outlet allows for easy installation.

• Polypropylene base plate: 340 x 185 x 80 mm (W x H x D).
• Polypropylene spigot: 600 mm.
• Stainless steel leaf guard: 345 x 140 x 100 mm (W x H x D).
• Thermofol Letterbox Parapet Outlet DN190: Flow rate 1.85 L/s.

Bauder outlets are sized to indicate the actual internal diameter of the spigot. For information on non-standard sizes and refurbishment applications, contact Bauder Technical Department.

BauderPVC NLF-R 50 emergency overflow.

Guidance for specification option:

An extruded PVC emergency overflow outlet compatible with Thermofol membrane.

• 50 mm diameter through wall overflow outlet manufactured in light grey colour.
• Flange dimeter: 160 mm.
• Spigot length: 480 mm.

For information on non-standard sizes and refurbishment applications, please contact Bauder Technical Department.

BauderPVC LSF embossed walkway membrane.

Guidance for specification option:

BauderPVC LSF embossed walkway is a 2 mm thick, reinforced PVC membrane with dark grey embossed finish to be loose laid over the finished membrane surface. The membrane should be heat welded around its full perimeter to the surface of the finished waterproofing.

BauderSOLAR F Photovoltaic Mounting System.

Guidance for specification option:

Bauder Flat roof PV mounting solution for framed solar modules. The mounting units are secured to the roof using a membrane-to-membrane welding technique. This installation method means that the roof is not compromised by penetrations for fixings nor is it ballasted, which would add additional weight loading to the roof. Specifically designed to be installed on Bauder bituminous or single ply waterproofing systems and provide a lightweight, low risk and quick to install mounting solution for framed solar modules.

For adhered and mechanically fastened Thermofol systems, (only suitable for use with U15 FB, U18 and U20).

Bauder LiquiFIBRE Detailing Kit.

Guidance for specification option:

Fast curing waterproofing resin containing fibre reinforcement that can be used for detailing awkward shapes or inaccessible areas where using LiquiDETAIL is impractical. PMMA-based resin that requires a catalyst and is solvent, isocyanate and halogen free.

Bauder LiquiDETAIL.

Guidance for specification option:

Cold liquid applied fast curing waterproofing resin that can be used on upstands and details. PMMA-based resin that requires the addition of catalyst to trigger curing and is solvent, isocyanate and halogen free.

Bauder rooflights/ glazing/ ventilation.

Guidance for specification option:

All these glazing products are fully compatible with the roof waterproofing systems. Consult Bauder for details and insert requirements.

• BauderDOME Rooflight.
• Bauder Euroglaze Rooflight.
• Bauder Special Modular Rooflight.
• Bauder Continuous Rooflight.
• Bauder Walk-on Rooflight.
• Bauder Direct Glazing.
• Bauder AOV.
• Bauder Modular Link Glazing.
• Bauder Structural Rooflight.
• Bauder Fire Rated Rooflight.