Verified by manufacturer 4 months ago
Single ply mechanically fixed roof covering system.
Suitable for mechanically fixed roofing applications.
Single ply mechanically fixed roof covering system.
System includes:
Color | Grey |
Finish | Matt |
Material | Polyvinyl chloride (PVC) |
Shape | Other |
Length | Bespoke |
Width | Bespoke |
Height | Bespoke |
Uniclass | |
CAWS | J42/10 Warm deck roof covering J42/110 Warm deck roof covering |
Lower protection layer | Spectratex, 300 g/m².Guidance for specification option: Spectratex geotextiles are a range of non-woven polyester geotextile isolation and protection layers. Used to protect the Spectraplan or Armourplan waterproofing membrane on ballasted or green roof build ups and can be used as a separation layer between PVC membranes and incompatible substrates such as existing bituminous membrane roofs or polystyrene thermal insulation boards. The Spectratex geotextiles are available in three grades – 300 gsm, 500 gsm, and 800 gsm. Heavier grades should be utilized in more onerous situations such as when overlaying an existing bituminous roof where it’s impractical to remove all of the chippings. The Spectratex geotextiles are installed loose laid with a 150mm side and end overlap. Spectratex, 500 g/m².Spectraxtex, 800 g/m². |
Air and vapour control layer | |
Type | Spectravap Polyethylene Vapour Control Layer.Guidance for specification option: Spectravap (blue) is a 0.3 mm thick polyethylene vapour control layer (VCL), suitable for use on most IKO Polymeric mechanically fastened systems. |
Attachment | Spectravap Jointing Tape.Guidance for specification option: Butyl tape, green, 19 x 1.5 mm x 30 m.
|
Insulation | |
Type | Enertherm ALU.Guidance for specification option: IKO enertherm ALU is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a multi-layer gastight aluminium complex. This high-quality reflecting ALU cladding consists of no fewer than seven layers, combined into a single complex. It is tested under extreme conditions in respect of water absorption, mechanical properties, corrosion resistance and emissivity. Consult literature for further details and insert requirements. |
Attachment | IKOfix Concrete Fastener.IKOfix Insulation Tube.IKOfix Universal Fastener.Thermally broken membrane washer. |
Waterproof covering | |
Type | Armourplan SM120, mid grey.Guidance for specification option: Insert width requirement: Available in three sizes: 1.06 m, 1.50 m and 2.12 m. Length: 20 m. Armourplan SM120, slate grey.Guidance for specification option: Insert width requirement: Available in three sizes: 1.06 m, 1.50 m and 2.12 m. Length: 20 m. Manufacturer guidanceArmourplan SM is a 1.2 mm thick polyester scrim reinforced membrane for mechanically fastened roofing systems on both flat and sloping roofs and is suitable for both new build and refurbishment installations. The membrane is mechanically fastened in the overlap using IKOfix Stress Plates and IKOfix Screws into the deck Overlaps are securely hot air welded. Armourplan SM can also be used for ballasted systems or alternatively in adhered systems bonded using Armourplan contact adhesive or Sprayfast PCA adhesive. Armourplan SM is also used as the upstand detailing membrane on all Armourplan SM/SG systems. |
Attachment | Armourplan PVC contact adhesive.Guidance for specification option: A ready to use nitrile rubber based contact adhesive used for adhering Armourplan SM and P membranes to various substrates. Blue in colour. Easy to apply using a brush or roller straight from the can. |
Accessories | None.Armourplan standing seam profile, mid grey.Guidance for specification option: Armourplan PVC Standing Seam Profile is a preformed profile used to simulate a metal standing seam joint. The profile is manufactured from PVC and is hot air welded to the installed Armourplan Membrane at a layout specified by the client Armourplan standing seam profile, slate grey. |
Upper protection layer | Spectratex, 300 g/m².Guidance for specification option: Spectratex geotextiles are a range of non-woven polyester geotextile isolation and protection layers. Used to protect the Spectraplan or Armourplan waterproofing membrane on ballasted or green roof build ups and can be used as a separation layer between PVC membranes and incompatible substrates such as existing bituminous membrane roofs or polystyrene thermal insulation boards. The Spectratex geotextiles are available in three grades – 300 gsm, 500 gsm, and 800 gsm. Heavier grades should be utilized in more onerous situations such as when overlaying an existing bituminous roof where it’s impractical to remove all of the chippings. The Spectratex geotextiles are installed loose laid with a 150mm side and end overlap. Spectratex, 500 g/m².Spectraxtex, 800 g/m². |
System accessories | Armourflow 2020 gutter.Guidance for specification option:
Armourplan membrane coated metal, mid grey.Guidance for specification option: Available in galvanized steel sheet form, 0.6 mm thick and can be fabricated off-site to form perimeter details such as drip edges and upstands. Armourplan membrane coated metal, slate grey.Guidance for specification option: Available in galvanized steel sheet form, 0.6 mm thick and can be fabricated off-site to form perimeter details such as drip edges and upstands. Armourplan membrane coated metal, light grey.Guidance for specification option: Available in galvanized steel sheet form, 0.6 mm thick and can be fabricated off-site to form perimeter details such as drip edges and upstands. IKO Strike PVC lightning conductor clips.Guidance for specification option: IKO Strike PVC lightning conductor clips are hot air welded to the surface of an IKO Polymeric membrane roof at 1 m centers The IKO Strike clip is a combination of a high quality rigid plastic clip attached to a 100 x 100 mm section of polyester reinforced membrane. Light grey in colour. The IKO Strike clip is designed to take uncoated lightning conductor tapes with a section of 25 mm wide x 3 mm thick. Cost effective and tidy solution to restraining rooftop lightning protection systems. IKO adjustable paving support pads.Guidance for specification option: IKO Adjustable Paving Support Pads are designed to be used where fine adjustment in height is required in order to obtain a level paved area on a roof deck. This is normally the case where the roof has been laid to falls for drainage, or where the deck is uneven. Consult literature for details and insert requirements. IKO paving support pads.Guidance for specification option: IKO Paving Support Pads incorporate spacing nibs to maintain a consistent drainage gap between pavings. They are easily divided into halves and quarters, for use at edges and corners of paved areas. IKO Paving Support Pads are primarily for use on consistent and level flat roof areas. Black in colour. 150 mm diameter x 15 mm high. IKO toothed flatbar.Guidance for specification option: Steel toothed flatbar used for securing the membrane at the perimeter of a mechanically fixed or ballasted polymeric roofing system. 1 x 2250 x 30 mm. Bespoke detail.Guidance for specification option: IKO Polymeric offers an in-house pre-fabrication department that can manufacture detail units to order from Armourplan D membrane. Consult manufacturer for details and insert requirements. IKO polymeric internal corner.Guidance for specification option: Internal and external corners manufactured from injection moulded PVC to suit a 90° corner can be simply installed over the Armourplan membrane field sheet and upstand and hot air welded into position. These form a reliable watertight solution to one of the most common roofing details. Colour: Mid grey. IKO polymeric external corner.Guidance for specification option: Internal and external corners manufactured from injection moulded PVC to suit a 90° corner can be simply installed over the Armourplan membrane field sheet and upstand and hot air welded into position. These form a reliable watertight solution to one of the most common roofing details. Colour: Mid grey. Armourplan membrane disc, mid grey.Guidance for specification option: Pre-cut 90 mm diameter membrane discs are available and are used when coving over intermediate fixing penetrations on Kingspan Topdek systems with an Armourplan membrane facing. These are simply hot air welded in to position to the panel surface. Armourplan membrane disc, light grey.Guidance for specification option: Pre-cut 90 mm diameter membrane discs are available and are used when coving over intermediate fixing penetrations on Kingspan Topdek systems with an Armourplan membrane facing. These are simply hot air welded in to position to the panel surface. Armourplan box scupper rainwater outlet, PVC Angled Roof Drain 180 mm.Guidance for specification option: Pre-formed outlets manufactured from PVC and are available in two width choices as standard. Light grey in colour. Provide a secure hot air welded solution to roof top drainage when used in conjunction with Armourplan membranes. Armourplan parapet rainwater outlet.Guidance for specification option: Pre-formed outlets manufactured from PVC and are available in various diameters. Light grey in colour. Provide a secure hot air welded solution to roof top drainage when used in conjunction with Armourplan membranes. IKO easy flow rainwater outlet system.Guidance for specification option: IKO Easy Flow parapet outlets are made from thermally insulated polyurethane. Yellow/black in colour. Available in a range of diameters with optional pipe lengths, IKO Easy Flow outlets enable effective drainage through the parapet wall up to 1m wide in to a rainwater hopper IKO Easy Flow outlets are available with pre-fitted flanges of the appropriate waterproofing material – Armourplan or Spectraplan to enable an effective waterproof detail. Diameter Range 70 & 100 mm. Spigot Length 500 & 1000 mm. Armourplan box scupper rainwater outletGuidance for specification option: Pre-formed outlets manufactured from PVC, 4 mm thick and are available in two width choices as standard. Light grey in colour. Provide a secure hot air welded solution to roof top drainage when used in conjunction with Armourplan membranes. Armourplan box scupper rainwater outlet, PVC Angled Roof Drain 300 mm.Guidance for specification option: Pre-formed outlets manufactured from PVC and are available in two width choices as standard. Light grey in colour. Provide a secure hot air welded solution to roof top drainage when used in conjunction with Armourplan membranes. Adjustable leaf guard.Guidance for specification option: Black adjustable leaf and gravel guard. Manufactured from robust polyamide material. Suitable for new build and refurbishment vertical drop rainwater outlets with spigot diameters from 60–200 mm. Easily adjusted to fit with no tooling necessary. Armourplan vertical rainwater outlet.Guidance for specification option: Pre-formed vertical drop outlets manufactured from injection moulded PVC. Grey in colour. Available in a wide range of diameters (50–160 mm external diameter, consult literature and insert requirements). Provide a secure hot air welded solution to roof top drainage when used in conjunction with Armourplan membranes. D95 Seal, small.D95 Seal, large.IKO trendy rainwater outlet system.Guidance for specification option: IKO Trendy roof outlet, Vertical, is made of thermally insulated polyurethane. Yellow in colour. Available in a range of diameters (70–125 mm, consult literature and insert requirements) to enable direct connection to pipes with push in spigot according to EN 1451-1 and EN 1124-2, for conventional gravity drainage The IKO Trendy outlets and extension units are available with pre- fitted flanges of the appropriate waterproofing material - Armourplan, Spectraplan or Bituminous VCL to enable an effective waterproof detail. When used with an IKO Trendy Extension Unit the outlet can provide a reliable airtight seal in conjunction with the VCL and thermal insulation up to 320 mm thick. PVC refurb rainwater outletGuidance for specification option: Pre-formed vertical drop outlets manufactured from injection moulded flexible PVC. Light grey in colour. Available in a wide range of diameters (45–128 mnm internal diameter, consult literature and insert requirements). Can be pushed into the existing rainwater outlet or downpipe in refurbishment applications where the fins can provide a watertight seal to the inside of the existing outlet. Provide a secure hot air welded solution to roof top drainage when used in conjunction with Armourplan membranes. |
Country of product manufacture | United Kingdom |