NBS Source
I'm a manufacturer

Stopgap 800 - Smoothing Compound

Verified by manufacturer 5 months ago

Ball, F and Co Ltd Third party certifications:
  • ISO 14001 Environmental Management Systems

    Certificate type

  • ISO 45001 Health and Safety Management

    Certificate type

  • ISO 9001 Quality Management

    Certificate type

  • DoP

    DoP

    Certificate type

  • M1 emission classification

    M1 emission classification

    Certificate type

Self-smoothing wearing surface.

Jump to:
+44 (0)1538 361633 Website

Application

PUMP APPLICATION

Mix in accordance with the pump manufacturers recommendations and adjust the rate of water flow until the mix is a smooth fluid, uniform grey liquid with no surface separation. Flow checks should be carried out at regular intervals during pumping.


APPLICATION

Pour the mixed material onto the prepared subfloor and allow to flow and attain a smooth finish. Minimal work with a smoothing trowel is required. A spiked roller should be used immediately to eliminate entrapped air and smooth out flow lines to give a more uniform surface appearance. The mixed material should be applied at a thickness between 5mm to 15mm. For optimum smoothing and levelling characteristics , an overall thickness of at least 5mm should be maintained.


DRYING / OVERCOATING

Drying is dependent on the absorbency of the subfloor, ambient temperature and humidity. On both absorbent surfaces and non-absorbent surfaces, at a nominal 5mm thickness, the compound will be ready to receive STOPGAP SEAL after a minimum of 6 hours.


STOPGAP SEAL is designed to protect the surface from spillage of water or other fluids. Please refer to the STOPGAP SEAL data sheet. If required, the surface may be sealed with other epoxy coatings / paints for aesthetic reasons, greater slip resistance in the wet or to improve chemical resistance. Please consult Technical Service Department for specific products.


NOTE

When used as a finish in domestic or design feature installations, it should be noted that consistency of colour / finish cannot be guaranteed. This is down to the naturally sourced components used within STOPGAP 800 and variations in mixing and application methods. To minimise such colour variation, material should be selected from the same batch date of manufacture. Colour differences do not effect the overall high performance of this product. This product is not recommended for external use. We do not recommend applying subsequent layers of STOPGAP 800 as this can lead to surface pinholing / irregularities.

Description

STOPGAP 800 is a self-smoothing commercial and industrial grade floor compound used for upgrading and renovating new and existing internal floors in light to heavy duty applications where floor coverings are not required to be installed. It is suitable for use in areas such as storerooms, post rooms, workshops, corridors, warehouses etc. STOPGAP 800 is grey in colour.


STOPGAP 800 is dimensionally stable and is supplied as a pre-blended dry powder, which is designed for application between 5-15mm. It is protein-free which allows it to be used in biologically sensitive areas.


STOPGAP 800 is for application over a wide range of subfloor types including sand / cement screed, concrete, granolithic, terrazzo, epoxy and polyurethane resins and STOPGAP waterproof surface membranes.


In areas where water or other fluids may come into direct contact with the cured material, the surface must be sealed with STOPGAP SEAL. This also helps to protect the floor surface and ease maintenance by reducing the adhesion of dirt and other debris.


STOPGAP 800 can also be pump applied.


COVERAGE

A 25kg bag of STOPGAP 800 mixed with 4.75 litres of clean water will cover approximately 3.0 m² at a thickness of 5 mm.


TECHINCAL INFORMATION

  • EN 13813 Class - CT-C35-F10-AR0.5
  • Abrasion Resistance (EN 13892-4) - AR0.5
  • Slip Resistance (without seal) Dry - 72 (EN 13036-4)Wet - 40
  • Working Time@ 20°C - 20 - 30 minutes
  • Walk on hardness time @ 20°C - 90 minutes
  • Time to traffic: Foot traffic - 3 hours Light traffic - 24 hours Heavy traffic - 3 days
  • Compressive Strength N/mm2 (EN13892-2) 1 Day - >20.0, 7 Days - >30.0, 28 Days - >35.0
  • Flexural Strength N/mm2 (EN13892-2) 1 Day - >4.0, 7 Days - >7.0, 28 Days - >10.0
  • Flow properties using 30mm ø x 50mm flow ring (EN 12706) - 120 - 140 mm
  • Consumption per mm thickness - 1.69kg / m2
  • Application thickness - 5 - 15mm


SURFACE PREPARATION

Floor surfaces must be suitably prepared: sound, dry (<75%RH) and free from contaminants that may prevent adhesion. Use STYCCOCLEAN C140 for removing grease, oil, polish soap etc. from non-absorbent substrates. Concrete and sand/cement screeds must be fully cured and any laitance or surface treatments must be removed.The temperature of the floor must be maintained above 10°C throughout the application and drying of the compound. Underfloor heating must be off for at least 48 hours before, during and after application.


PRIMING - IT IS ESSENTIAL TO PRIME ALL SURFACES Absorbent surfaces – Prime with a minimum 2 coats of dilute STOPGAP P131 to prevent uncontrolled rapid drying of the compound which may lead to surface pin holing, poor flow characteristics, surface imperfections and colour variation. Very absorbent surfaces may need additional coats of primer. If applying over STOPGAP 600, this should be done within 24 hours and the surface should first be primed with a dilute coat of primer followed by a neat coat.


Non-absorbent surfaces - such as terrazzo, quarry tiles and STOPGAP waterproof surface membranes should be primed with neat STOPGAP P141.


Apply the primer using a soft brush and do not extend the stated coverage. Site and substrate conditions vary, the chosen priming system should be evaluated over a trial area to ensure an optimum surface finish.


Alternatively, STOPGAP F77 may be used as a priming system in conjunction with a kiln dried grit 0.7-1.2mm:


Damp subfloors: Install STOPGAP F77 waterproof surface membrane as directed and within 24 hours apply a second coat of STOPGAP F77. Whilst still wet, fully blind the surface with the grit and allow to cure before vacuuming away all loose grit and installing STOPGAP 800.


Dry, absorbent subfloors: Apply one coat of STOPGAP F77 and whilst still wet, fully blind the surface with the grit and allow to cure before vacuuming away all loose grit and installing STOPGAP 800.


MIXING

Add 4.75 litres of clean water into a STOPGAP mixing bucket and gradually add all the powder whilst stirring with a power whisk fitted in an electric drill until a smooth creamy lump free consistency is achieved. The material should be mixed for a minimum of 2 minutes.


WATER ADDITION

4.5 litres minimum - 5.0 litres maximum per 25kg depending on consistency and flow properties required. Do not exceed 5.0 litres of water per 25kg bag.

General information

Color

Grey

Finish

Smooth

Material

Cementitious

Shape

Formless

Length

Bespoke

Width

Bespoke

Height

Bespoke

Warranty description

Lifetime

Uniclass

Pr_35_31_06_80 Smoothing and levelling underlay compoundsPrimary

CAWS

M10/160 Proprietary self smoothing levelling screeds

M10/7 Proprietary quick drying levelling screeds

Specification data - Smoothing and levelling underlay compounds

Material

Cementitious.

Standards

To EN 13813:2002.

Guidance for specification option:

CT-C40-F10-AR0.5.

Working time

20–30 minutes at 20°C.

Setting time

90 minutes at 20°C.

Consumption (per layer applied)

1.69kg/m² per mm thickness.

Compressive strength - 1 day

>20.0 N/mm².

Manufacturer guidance

To EN13892-2.

Compressive strength - 7 days

>30.0 N/mm².

Manufacturer guidance

To EN13892-2.

Compressive strength - 28 days

>35.0 N/mm².

Manufacturer guidance

To EN13892-2.

Flexural strength

1 Day: >4.0 N/mm²; 7 Days: >7.0 N/mm²; 28 Days: >10.0 N/mm².

Manufacturer guidance

To EN13892-2.

Sustainability data

Contains Red List materials

No

Country of material origin

Europe

Country of product manufacture

United Kingdom

Recyclability

Paper Sack

Recycled content

As defined in clause 7.8 of BS EN ISO 14021

0 %

Third party certifications

Third party certifications

ISO 14001 Environmental Management Systems

ISO 14001 Environmental Management Systems

ISO 14001:2015

ISO 45001 Health and Safety Management

ISO 45001 Health and Safety Management

ISO 45001:2018

ISO 9001 Quality Management

ISO 9001 Quality Management

ISO 9001:2015

DoP

DoP

Stopgap 800 Wearcoat CE

M1 emission classification

M1 emission classification

Stopgap 800 Wearcoat Emicode

DoP

DoP

Stopgap 800 Wearcoat UKCA

Literature

Flooring Installation Products

Flooring Installation Products

Stopgap 800 Wearcoat TDS

Stopgap 800 Wearcoat TDS

Stopgap 800 Wearcoat SDS

Stopgap 800 Wearcoat SDS

Case studies

Travis Perkins, Long Eaton - Stopgap 800 Wearcoat provides a strong grounding at Travis Perkins

Travis Perkins, Long Eaton - Stopgap 800 Wearcoat provides a strong grounding at Travis Perkins

Similar products from Ball, F and Co Ltd

Stopgap 1100 - Smoothing Compound

Stopgap 1100 - Smoothing Compound

Stopgap 1200 - Smoothing Compound

Stopgap 1200 - Smoothing Compound

Stopgap 1400 - High Flow Smoothing Compound

Stopgap 1400 - High Flow Smoothing Compound

Stopgap 1500 - Smoothing Compound

Stopgap 1500 - Smoothing Compound

Stopgap 300 - Smoothing Compound

Stopgap 300 - Smoothing Compound

Stopgap 500 Micro - Repair Mortar

Stopgap 500 Micro - Repair Mortar

Stopgap 600 Base - Smoothing Compound

Stopgap 600 Base - Smoothing Compound

Stopgap 700 - Smoothing Compound

Stopgap 700 - Smoothing Compound

Stopgap 850  - Smoothing Compound

Stopgap 850 - Smoothing Compound

Stopgap Green Bag - Smoothing Compound

Stopgap Green Bag - Smoothing Compound