NBS Source
I'm a manufacturer

RubberGard™ EPDM Mechanically Attached Warm Roof System

Verified by manufacturer 1 day ago

Elevate EMEA Third party certifications:
  • BBA Agrément Certificate

    BBA Agrément Certificate

    Certificate type

A lightweight, non-penetrating, mechanically attached EPDM warm roof system.

Jump to:
+44 (0)1565 756186 Website

Application

Suitable for profiled metal deck applications and other deck types which provide sufficient anchorage for mechanical attachment.

Description

The RubberGard™ EPDM RMA System is a lightweight, non-penetrating mechanically attached system developed around the QuickSeam™ RMA strip: a strip of reinforced EPDM membrane incorporating two strips of self-adhesive QuickSeam™ Splice Tape laminated along each edge over the length of the strip.


Features and benefits:

  • Non-penetrating.
  • Use of large EPDM sheets.
  • Fewer seams.
  • Fast coverage.
  • Lightweight system.
  • Aesthetics.
  • High wind uplift performance.
  • Safe, flame-free installation.


System components:

  • RubberGard™ EPDM LSFR.
  • QuickSeam™ RMA strip.
  • ISOGARD™ AK PIR Insulation.
  • ISOGARD™ MG PIR Insulation.
  • RESISTA™ AK PIR Insulation.
  • RESISTA™ MG PIR Insulation.
  • Air and vapour control layer.
  • Bonding Adhesive BA-2012 (for vertical membrane application).

General information

Color

Black

Finish

Smooth

Material

Rubber

Polyisocyanurate (PIR)

Shape

Rectangle

Length

30500 mm

Width

3050 mm

6100 mm

9150 mm

Height

1.1 mm

1.5 mm

Warranty description

Ten year

15 year

20 year

Uniclass

Ss_30_40_30_80 Single layer sheet warm roof covering systemsPrimary

CAWS

J42/10 Warm deck roof covering

J42/110 Warm deck roof covering

Specification data - Single layer sheet warm roof covering systems

Preparation

-

Horizontal work

The substrate will be securely fixed, clean, dry, smooth and free of contaminants such as greases, animal fats, coal tar and oil-based products. All sharp edges, nibs and rough surfaces which could damage the membrane will be removed or otherwise isolated.

Air and vapour control layer

-

Type

Elevate V-Gard ALU 1500 self-adhesive air and vapour control layer.

Elevate V-Gard PE 200 air and vapour control layer.

Elevate V-Gard PE 200 E air and vapour control layer.

Elevate V-Gard PE 400 air and vapour control layer.

Manufacturer guidance

V-Gard ALU 1500

Use where insulation layer is to be mechanically attached through the AVCL. Self-adhesive to approved substrates (wood, steel).

V-Gard PE 200, V-Gard PE 200 E, V-Gard PE 400

Use where insulation layer is to be mechanically attached through the AVCL (low humidity class buildings only). Loose laid over the approved substrate, joints are taped using V-Gard PE Seam Tape.

Attachment

As type.

Insulation

-

Type

ISOGARD AK PIR Insulation.

Guidance for specification option:

Thermal conductivity: 0.023 W/m.K.

Thickness: 30–160 mm. Insert requirements.


Elevate ISOGARD AK insulation board consists of a closed-cell polyiso (PIR) foam core laminated on both sides to a gastight multi-layered aluminium complex.

ISOGARD MG PIR Insulation.

Guidance for specification option:

Thermal conductivity: 0.025–0.028 W/m.K.

Thickness: 30–160 mm. Insert requirements.


Elevate ISOGARD MG insulation board consists of a closed-cell polyiso (PIR) foam core laminated on both sides to a gasopen mineral glassfibre facer.

RESISTA AK PIR Insulation.

Guidance for specification option:

As per Fully Adhered Warm Roof System spec.


Thermal conductivity: 0.023 W/m.K.

Thickness: 30–160 mm. Insert requirements.


Elevate RESISTA AK insulation board consists of a closed-cell polyiso (PIR) foam core laminated on both sides to a gastight multi-layered aluminium complex.

RESISTA MG PIR Insulation.

Guidance for specification option:

As per Fully Adhered Warm Roof System spec.


Thermal conductivity: 0.025–0.028 W/m.K.

Thickness: 30–160 mm. Insert requirements.


Elevate RESISTA MG insulation board consists of a closed-cell polyiso (PIR) foam core laminated on both sides to a gasopen mineral glassfibre facer.

Manufacturer guidance

Consult the manufacturer's Technical Services Department for R-Value/U-value calculations as required.

Attachment

Insulation plates and fasteners.

Guidance for specification option:

The fastening pattern is chosen in line with the manufacturer's installation guidelines and to accommodate for wind loading.

Waterproof covering

-

Type

RubberGard™ EPDM LSFR Roofing Membrane 1.1 mm.

RubberGard™ EPDM LSFR Roofing Membrane 1.5 mm.

Manufacturer guidance

100% cured non-reinforced, Ethylene-Propylene-Diene Terpolymer (EPDM) synthetic rubber, manufactured in an ISO 9001 and ISO 14001 registered facility. Minimum unspliced width of 3.05 m.

Specification compliance:

UL Classified/ FM Approved.

ASTM D 4637/ EN 13956 (CE Mark).

7500 hrs of Artificial Ageing as per EN 1297.

Attachment

QuickSeam RMA strip.

Guidance for specification option:

Secured to the steel deck using approved plates/batten bars and fasteners. Spacing of the plates and/or fasteners differs to accommodate for wind loadings and are positioned according to the parameters of the wind load calculation based on local or international standards.

Joints

Lap splices: 100 mm minimum overlap with 76 mm QuickSeam Splice Tape.

Surface protection

QuickSeam Walkway Pads.

Guidance for specification option:

760 x 760 mm high quality rubber pads with QuickSeam Tape factory laminated to the bottom. They are used for protection of the Elevate RubberGard EPDM membrane in areas of regular roof traffic (periodical maintenance around mechanical equipment, access doors, etc.).

System accessories

QuickSeam Splice Tape.

QuickSeam FormFlash.

QuickSeam Flashing.

QuickSeam SA Flashing.

QuickSeam Reinforced Perimeter Fastening Strip.

QuickSeam Universal Pipe Flashing.

QuickSeam Conduit Flashing.

QuickSeam Penetration Pocket.

QuickSeam Walkway Pad.

QuickPrime Plus.

Lap Sealant HS.

All Purpose (AP) Fasteners.

Heavy Duty (HD) Fasteners.

Splice Wash (SW-100).

Cleaner C-20.

Water-Block Seal (S-20).

Pourable Sealer S-10 (Parts A & B).

Coiled Metal Batten Strip.

Metal Batten Strip.

Termination Bar.

Corners

QuickSeam FormFlash (external corners) and folded internal corners.

Pipes

Pipe penetrations: QuickSeam FormFlash.

Pipe penetrations: QuickSeam Pipe boots and Conduit Flashing.

Outlets

Drains: Install Water Block Sealant between membrane and outlet bowl. Secure membrane mechanically to outlet using integral clamping ring.

Drains: Insert outlet bedded on Water Block Sealant. Secure and flash with QuickSeam FormFlash or SA Flashing.

Walls

Wall terminations: Termination bar, fastened with Water Block Sealant and Lap Sealant HS installed along top edge.

Guidance for specification option:

@200mm (maximum) o.c.

Wall terminations: Metal batten bar fastened with surface mounted or inserted metal counter flashing protection.

Guidance for specification option:

@150mm (maximum) o.c.

Wall terminations: Metal capping or concrete coping stones.

Wall termination: Preformed metal edge trim.

Guidance for specification option:

An appropriate metal edge trim will be prefabricated and installed with fasteners @ maximum 100 mm centres. The edge trim will be sealed with QuickSeam Flashing.

Sustainability data

Country of product manufacture

United States

Material

Rubber

Polyisocyanurate (PIR)

Recyclability

An Environmental Product Declaration (EPD) is available upon request.

BIM objects

Platform Compatible Version
Revit
-

1

Third party certifications

BBA Agrément Certificate

BBA Agrément Certificate

Elevate RubberGard EPDM Systems

Literature

RubberGard™ EPDM

RubberGard™ EPDM

Similar products from Elevate EMEA

Rhenofol® PVC-P Mechanically Attached Warm Roof System - Single Ply PVC-P Warm Roof System

Rhenofol® PVC-P Mechanically Attached Warm Roof System - Single Ply PVC-P Warm Roof System

RubberGard™ EPDM Ballasted Warm Roof System

RubberGard™ EPDM Ballasted Warm Roof System

RubberGard™ EPDM Fully Adhered Warm Roof System

RubberGard™ EPDM Fully Adhered Warm Roof System

RubberGard™ EPDM Inverted Warm Roof System

RubberGard™ EPDM Inverted Warm Roof System

RubberGard™ EPDM SA Fully Adhered Warm Roof System - Self-adhesive EPDM Single Ply Roofing

RubberGard™ EPDM SA Fully Adhered Warm Roof System - Self-adhesive EPDM Single Ply Roofing

UltraPly™ TPO  Inverted Warm Roof System

UltraPly™ TPO Inverted Warm Roof System

UltraPly™ TPO Ballasted Warm Roof System

UltraPly™ TPO Ballasted Warm Roof System

UltraPly™ TPO Fully Adhered Warm Roof System

UltraPly™ TPO Fully Adhered Warm Roof System

UltraPly™ TPO Mechanically Attached Warm Roof System  - Single Ply Membrane Warm Roof System

UltraPly™ TPO Mechanically Attached Warm Roof System - Single Ply Membrane Warm Roof System